Why removable stickers change your campaign
Frosthaven’s campaign normally uses permanent stickers for scenarios, enhancements, and buildings. Once placed, those stickers are meant to stay. The Frosthaven: Removable Sticker Set replaces all of those normal stickers with vinyl versions that can be removed at any time with no damage to the components. That single change turns every sticker decision into a reversible one—useful if you like to rethink map layout, try different enhancement combinations, or simply keep your game in flexible condition for future play.
This guide covers how to apply, remove, and reposition the stickers, plus how to care for them between sessions. The advice is based on the product’s stated capability; where the supplied information does not include a specific step, we say so rather than guess.
What the sticker set actually replaces
- Frosthaven: Removable Sticker Set: This set of vinyl stickers replaces all of the normal scenario, enhancement, and building stickers in Frosthaven. You get a removable version of every sticker type used during the campaign, so you can plan your board without committing permanently.

Frosthaven: Removable Sticker Set - Frosthaven: Removable Sticker Set: If you don't like the permanence of normal stickers, these vinyl stickers can be removed at any time with no damage to the components. This is the core benefit: you can undo a placement without harming the map tile, card, or building board.
How to apply, remove, and reposition your stickers
The supplied information confirms that the stickers are removable without damage, but it does not include a detailed application procedure. The steps below are general best practices for removable vinyl stickers and should be treated as practical guidance, not manufacturer instructions. Always test on a small, inconspicuous area first if you are unsure.
- Start with clean, dry hands and surfaces: Oils and dust can weaken adhesion. Make sure the component surface is dry and free of debris before placing a sticker.
- Peel the sticker from its backing slowly: A slow, even peel helps prevent stretching or curling. Avoid touching the adhesive side with your fingers.
- Position lightly before pressing: Set the sticker in place with light pressure so you can still lift it if the alignment is off. Once satisfied, press down firmly from the center outward.
- To remove, lift a corner gently: Use a fingernail or a thin, blunt tool to start lifting a corner. Pull back slowly and at a low angle rather than yanking upward.
- Reposition while the adhesive is still fresh: If you need to move a sticker, remove it carefully and reapply. The vinyl is designed to be removable, but repeated repositioning in a short period may reduce tackiness over time.
Care tips for long-term reuse
To keep your removable stickers working well across a long campaign, store unused stickers flat in their original backing sheet or a smooth, dust-free container. Avoid leaving them in direct sunlight or hot cars, which can make vinyl more difficult to handle. When you remove a sticker during play, keep it on a clean surface or back on its backing rather than letting it pick up lint or crumbs.
If a sticker loses its grip after many repositions, the supplied information does not include a recommended fix. In that case, consider whether the sticker is essential to the current scenario or whether you can note the information separately. The set’s value is in flexibility, not in unlimited re-sticking.
Removable vs. permanent: what changes at the table
The trade-off is straightforward. Permanent stickers are a one-time commitment; removable stickers give you an undo button but may require a little more handling care.
- Removable vinyl stickers: Can be removed at any time with no damage to components. Better for players who want to experiment, reset, or keep components in reusable condition.
- Normal permanent stickers: Intended to stay in place permanently. Once applied, they are not designed to be removed without potentially damaging the component.
Storing your sticker set between sessions
Keep the unused stickers and any removed stickers in a cool, dry place. A small zip bag or the original backing sheet works well. Label the bag if you are separating scenario, enhancement, and building stickers so you can find the right type quickly during setup. Because the set replaces all three sticker categories, a simple sorting system will save time later.
If you remove a sticker during play and plan to reuse it, place it adhesive-side down on a clean, non-stick surface such as the backing paper. Avoid stacking stickers directly on top of each other, as they may stick together and become difficult to separate.


